hello comrades! It’s been a minute! I’m back with my first tech update since upending my entire life and getting re-settled! Let’s talk meow-coffee

What I’ve been up to

See for yourself, pictured is the first alpha of the Sphynx Lite. Schematics are on git, go check it out (and if you want to set up KiCAD to view or edit but aren’t quite sure how, say so in the comments and me or someone else will help you out!)

Issuing guidance on the usage of these things is complicated. I’m always going to be a little apprehensive recommending that people use this, because I’m a very cautious person. For now, I think my official guidance is:

  • you should understand the circuit
  • you should have basic debugging equipment
  • you should have the time to work with it extensively
  • if you meet all of the above, I provide this with no warranty and no guarantee, knowing you full well have ideas as to what you might want to use it for
  • If you have a decent working knowledge of electrical engineering and want a walkthrough, I might make a Matrix so I can actually communicate with people looking to get it going??

As it gets more mature and I revise and revise until I drop the alpha, I’ll trust it more.

This was a push across the finish line. I optimized for getting something testable done with the correct topology, layout is a little dicey (cut off silk screen in the bottom right kitty-cri) and subject to change, I just needed something to test on. I was gone for over two weeks from my last post here, mainly because it was just a lot of work with nothing intermediate to report. But now it’s here! This has all the working parts of the last boards merged into one, with the new additions of:

  • power conditioning
  • 9V battery holders
  • additional safety measures, like the redundant current limiting JFET
  • configuration jumpers! and test points!! !!!

Oh, and I whipped up a cute lil logo. :3

Schematics

schematics in here

Board Layout

board layout in here

Board Renders

board renders in here

Next up

I have a lot of really good work from y’all that I need to capture and incorporate. Particularly, my immediate plans while this board is fabricated and shipped are to:

  • Incorporate @ComradeEd@lemmygrad.ml’s patchset porting the site to Jekyll - really thank you so much for this, I’ve been extremely focused on the board, and now that I have a minute, I can get the site going so I can use it to show off, post guide, aggregate educational resources, etc. This is going to be absolutely necessary for the project to have the reach and accessiblilty I’m hoping it gets. Thank you. meow-hug
  • Build a probe per @YearOfTheCommieDesktop@hexbear.net’s work into coming up with a probe holder. I have a handful of the Yasutomo’s to experiment with. This is going to be a game changer, currently I’m doing self-work with an alligator clip and it’s extremely irritating. An ergonomic and reproducible probe with an extremely cheap parts list is critical for the project to function. Thank you. meow-hug
  • More of you provided meaningful help than just these two, these are the two who’s work I’m directly interacting with this minute. Thank you to everyone who has stopped by and made suggestions, I’ve read them all. meow-hug

The next post will be me building this out and reporting on how well (or whether) it works, and documenting changes for the Lite Alpha 2.

I also badly need to make a BOM. With some effort, anyone who’s built a board together can buy all the parts for this and make one, but it’d be a thousand times easier if I just made a single cart that you can buy that includes every single component. If you want to make an alpha board for fun or debugging, maybe hold off until I have that out.

Any ways to help?

Honestly, those of you who are following this pretty closely have a good read on what’s going on, what’s needed, and what’s upcoming - keep being interested! If anyone wants to make one, I do recommend waiting until I release a BOM, but very soon we miiight be at the point where other people besides me get one of these in their hands.

I could also use some polish on the logo. It’s fine, but it could be cuter, and the lines are a bit funky. I’m going to put SVGs on git soon and if anyone feels like cleaning them up, rearrange the kitty cat face so it’s cuter, fixing my wonky paths, let me know!

Also, and I simply cannot stress this enough - when I’ve been exhausted, when I’ve been deep in executive dysfunction, when I’ve been not feeling up for it, I’ve read through all your encouragement and support throughout the duration of this project and it’s helped me to keep pushing. I would unquestionably not be this far without y’all. Thank you all so much. trans-heart


As always, stop by, hang out, say hi, ask questions, tell me what you’ve been up to, design review me, however you’d like to be involved is good by me! I’m thinking I want to make the expected cadence of posts once every two weeks, just because I’m busy and I don’t want to cause alarm when I miss a week. I can always surprise y’all with more frequent posts too.


P.S. - I have no hair regrowth in test areas. meow-melt

  • macerated_baby_presidents [he/him]@hexbear.net
    link
    fedilink
    English
    arrow-up
    5
    ·
    6 months ago

    what the fuck they’re on kicad 8 already? I remember complaining about the upgrade to 6. Would you like to upload a render of the back of the board? I don’t wanna upgrade yet I’m in the middle of another project. I’m probably gonna get after you for wasted space (and those on-board 9V holders) but tbh PCBs are surprisingly cheap these days. Are you thinking about making a case for it?

    at least for prototype BOM, I suggest just putting all the parts in Digikey or Mouser and using their “share cart” link. you probably have to order stuff anyway so it’s pretty painless. Good work so far!

    • 410757864530_dead_follicles [she/her]@hexbear.netOP
      link
      fedilink
      English
      arrow-up
      4
      ·
      6 months ago

      just updated the post with schematics, renders, and board layout! Thanks for stopping in!

      Version 8 is cool! I started the project in 7 and the upgrade didn’t break anything, although it changed the whitespace formatting in text files so I had some crazy git commits. It also comes with some nice but fairly modest features. https://www.kicad.org/blog/2024/02/Version-8.0.0-Released/

      Yeah wasted space is definitely a thing here lol, I just wanted to get something usable out the door. I’ll re-pack everything for Alpha 2. Honestly this is pretty bad layout on my part, I focused on laying out each module well, and then at the board level I kinda just slapped things together. It would make JLCPCB kinda impossible, but I sorta love the idea of putting the battery holders on the bottom and using them as feet, and routing in the space on top of them. We’ll see, but I’m really prioritizing JLCPCB orderability at some point, if not right now, for the accessibility, which kinda means everything on top. I’m also inbetween price tiers, I think: 100mm x 200mm is where I’m at now, and the next tier down is like 100mm x 100 mm, which I’ll never hit. I’m barely over 100mm x 150mm, so I figured I might as well just use the space if it’s free. But I totally will repack in the Alpha 2.

      I am thinking of an optional enclosure, but that’s for someone in the community to implement if they’d like to! It’d be a quality of life improvement, I’m worried about it getting shorted on stuff as a naked board, but this is also definitely not the final form factor, so nobody should start on that quite yet.

      Mouser share cart is the plan for now!

      • macerated_baby_presidents [he/him]@hexbear.net
        link
        fedilink
        English
        arrow-up
        5
        ·
        edit-2
        6 months ago

        *bonk* you already know what I’m gonna say, this board could be a quarter of the size if you packed it and put components on both sides. Even if you stay single-sided components for assembly, I totally think you could do 100x100mm if you removed the 9V holders and used pigtail-style 9V holders, or (if that causes trouble for assembly) even barrel jacks and some off-the-shelf holders for users.

        I like submodules (hierarchical sheets? I’m still on kicad 6 lol) for schematic organization but I guess they make it harder to make your board dense since you end up trying to pack rectangles together.

        But I looked at the JLCPCB prices and squishing it down is probably only necessary for your pride. If you start distributing these in numbers high enough for the cost to justify the extra trouble, somebody will rip off the design and start selling it on Amazon and it won’t be your problem anymore.

        I will say that committing to an enclosure helps other stuff a bit. Instead of needing the big board space for the batteries, you can just have a pigtail holder and a place in the case where the batteries sit. Depending on how you did it, you’d also have more freedom in (a) less silkscreen space around the pots (b) components between the pots without users brushing them with their fingers. FreeCAD actually has a plugin to import KiCAD models from the 3d view (and then export to some other tool’s format if FreeCad isn’t your jam) so you could make a simple 3d printed case or something. Or (deja vu, sorry if I’ve already suggested this) you could put it into a guitar pedal case. Seems like a natural fit with the 1/4" jack. Once the project is solidified a bit more and I’m less busy I’m likely to order a board, try it out, and possibly design a case.